Enric a 20:13, 27 oct 2015

2015-10-27T20:13:51Z

Gerard a 08:43, 27 oct 2015

2015-10-27T08:43:12Z

Enric: Es crea la pàgina amb « #include // Used for Ethernet #define FILTERSETTLETIME 5000 // Time (ms) to allow the filters to...».

2015-10-20T17:34:04Z

Es crea la pàgina amb « #include <UIPEthernet.h> // Used for Ethernet #define FILTERSETTLETIME 5000 // Time (ms) to allow the filters to...».

Pàgina nova

#include <UIPEthernet.h> // Used for Ethernet
#define FILTERSETTLETIME 5000 // Time (ms) to allow the filters to settle before sending data
#define SERIALPRINT // include print statement for commissioning - comment this line to exclude
#define PHASE2 8 // Number of samples delay for L2
#define PHASE3 17 // Number of samples delay for L3, also size of array
#define RF69_COMPAT 0 // set to 1 to use RFM69CW
const int UNO = 0; // Set to 0 if you are not using the UNO bootloader
// **** ETHERNET SETTING ****
byte mac[] = { 0x54, 0x34, 0x41, 0x30, 0x30, 0x90 };
IPAddress ip(192, 168,1,190);
EthernetServer server(80);
int inPinV = 6;
int inPinI1 = 1;
int inPinI2 = 4;
int inPinI3 = 7;
//Calibration coefficients - see http://openenergymonitor.org/emon/modules/emontx/firmware/calibration%20
//These need to be set in order to obtain accurate results
double Vcal = 157.8; // Calibration - constant for voltage input - for ideal power voltage adapter
double Ical1 = 60.6; // Calibration constant for current transformer 1
double Ical2 = 60.6; // Calibration constant for current transformer 2
double Ical3 = 60.6; // Calibration constant for current transformer 3
double Phasecal1 = 1.0; // Calibration constant for phase shift L1
double Phasecal2 = 1.6; // Calibration constant for phase shift L2
double Phasecal3 = 1.0; // Calibration constant for phase shift L3
//--------------------------------------------------------------------------------------
// Variable declaration for filters, phase shift, voltages, currents & powers
//--------------------------------------------------------------------------------------
int lastSampleV,sampleV; //sample_ holds the raw analog read value, lastSample_ holds the last sample
int lastSampleI1,sampleI1;
int lastSampleI2,sampleI2;
int lastSampleI3,sampleI3;
double lastFilteredV,filteredV; //Filtered_ is the raw analog value minus the DC offset
double lastFilteredI1, filteredI1;
double lastFilteredI2, filteredI2;
double lastFilteredI3, filteredI3;
double phaseShiftedV1; //Holds the calibrated delayed & phase shifted voltage.
double phaseShiftedV2;
double phaseShiftedV3;
double sqV,sumV,sqI1,sumI1,sqI2,sumI2,sqI3,sumI3;
double instP1,sumP1,instP2,sumP2,instP3,sumP3; //sq = squared, sum = Sum, inst = instantaneous
int startV; //Instantaneous voltage at start of sample window.
double realPower1, // The final data
apparentPower1,
powerFactor1,
Irms1,
realPower2,
apparentPower2,
powerFactor2,
Irms2,
realPower3,
apparentPower3,
powerFactor3,
Irms3,
Vrms;
typedef struct { int power1, power2, power3, Vrms; } PayloadTX; // neat way of packaging data for RF comms
// (Include all the variables that are desired,
// ensure the same struct is used to receive)
PayloadTX emontx; // create an instance
const int LEDpin = 9; // On-board emonTx LED
boolean settled = false;
void setup() {
Serial.begin(9600);
// start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("IP Address: ");
Serial.println(Ethernet.localIP());
pinMode(LEDpin, OUTPUT); // Setup indicator LED
digitalWrite(LEDpin, HIGH);
}
void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client)
{
Serial.println("-> New Connection");
calcVI3Ph(11,2000);
// Removing these print statements is recommended for normal use (if not required). Not used Gerard
/*#ifdef SERIALPRINT
Serial.print("Voltage: "); Serial.println(Vrms);
Serial.print(" Current 1: "); Serial.print(Irms1);
Serial.print(" Power 1: "); Serial.print(realPower1);
Serial.print(" VA 1: "); Serial.print(apparentPower1);
Serial.print(" PF 1: "); Serial.println(powerFactor1);
Serial.print(" Current 2: "); Serial.print(Irms2);
Serial.print(" Power 2: "); Serial.print(realPower2);
Serial.print(" VA 2: "); Serial.print(apparentPower2);
Serial.print(" PF 2: "); Serial.println(powerFactor2);
Serial.print(" Current 3: "); Serial.print(Irms3);
Serial.print(" Power 3: "); Serial.print(realPower3);
Serial.print(" VA 3: "); Serial.print(apparentPower3);
Serial.print(" PF 3: "); Serial.println(powerFactor3);
Serial.println(); delay(100);
#endif */
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected())
{
if (client.available())
{
char c = client.read();
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank)
{
client.print(Vrms);
client.print(" ");
client.print("L1 ");
client.print(Irms1);
client.print(" ");
client.print(realPower1);
client.print(" ");
client.print(apparentPower1);
client.print(" ");
client.print(powerFactor1);
client.print(" ");
client.print("L2 ");
client.print(Irms2);
client.print(" ");
client.print(realPower2);
client.print(" ");
client.print(apparentPower2);
client.print(" ");
client.print(powerFactor2);
client.print(" ");
client.print("L3 ");
client.print(" ");
client.print(Irms3);
client.print(" ");
client.print(realPower3);
client.print(" ");
client.print(apparentPower3);
client.print(" ");
client.print(powerFactor3);
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r')
{
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(10);
// close the connection:
client.stop();
Serial.println(" Disconnected\n");
}
}
void calcVI3Ph(int cycles, int timeout)
{
int SupplyVoltage = readVcc();
int crossCount = 0; // Used to measure number of times threshold is crossed.
int numberOfSamples = 0; // This is now incremented
int numberOfPowerSamples = 0; // Needed because 1 cycle of voltages needs to be stored before use
boolean lastVCross, checkVCross; // Used to measure number of times threshold is crossed.
double storedV[PHASE3]; // Array to store >120 degrees of voltage samples
//-------------------------------------------------------------------------------------------------------------------------
// 1) Waits for the waveform to be close to 'zero' (500 adc) part in sin curve.
//-------------------------------------------------------------------------------------------------------------------------
boolean st=false; // an indicator to exit the while loop
unsigned long start = millis(); // millis()-start makes sure it doesnt get stuck in the loop if there is an error.
while(st==false) // Wait for first zero crossing...
{
startV = analogRead(inPinV); // using the voltage waveform
if ((startV < 550) && (startV > 440)) st=true; // check it's within range
if ((millis()-start)>timeout) st = true;
}
//-------------------------------------------------------------------------------------------------------------------------
// 2) Main measurment loop
//-------------------------------------------------------------------------------------------------------------------------
start = millis();
while ((crossCount < cycles * 2) && ((millis()-start)<timeout))
{
lastSampleV=sampleV; // Used for digital high pass filter - offset removal
lastSampleI1=sampleI1;
lastSampleI2=sampleI2;
lastSampleI3=sampleI3;
lastFilteredV = filteredV;
lastFilteredI1 = filteredI1;
lastFilteredI2 = filteredI2;
lastFilteredI3 = filteredI3;
//-----------------------------------------------------------------------------
// A) Read in raw voltage and current samples
//-----------------------------------------------------------------------------
sampleV = analogRead(inPinV); // Read in raw voltage signal
sampleI1 = analogRead(inPinI1); // Read in raw current signal
sampleI2 = analogRead(inPinI2); // Read in raw current signal
sampleI3 = analogRead(inPinI3); // Read in raw current signal
//-----------------------------------------------------------------------------
// B) Apply digital high pass filters to remove 2.5V DC offset (to centre wave on 0).
//-----------------------------------------------------------------------------
filteredV = 0.996*(lastFilteredV+sampleV-lastSampleV);
filteredI1 = 0.996*(lastFilteredI1+sampleI1-lastSampleI1);
filteredI2 = 0.996*(lastFilteredI2+sampleI2-lastSampleI2);
filteredI3 = 0.996*(lastFilteredI3+sampleI3-lastSampleI3);
storedV[numberOfSamples%PHASE3] = filteredV; // store this voltage sample in circular buffer
if (crossCount > 2) // one complete cycle has been stored, so can use delayed
{ // voltage samples to calculate instantaneous powers
//-----------------------------------------------------------------------------
// C) Root-mean-square method voltage
//-----------------------------------------------------------------------------
sqV= filteredV * filteredV; //1) square voltage values
sumV += sqV; //2) sum
//-----------------------------------------------------------------------------
// D) Root-mean-square method current
//-----------------------------------------------------------------------------
sqI1 = filteredI1 * filteredI1; //1) square current values
sumI1 += sqI1; //2) sum
sqI2 = filteredI2 * filteredI2;
sumI2 += sqI2;
sqI3 = filteredI3 * filteredI3;
sumI3 += sqI3;
//-----------------------------------------------------------------------------
// E) Phase calibration - for Phase 1: shifts V1 to correct transformer errors
// for phases 2 & 3 delays V1 by 120 degrees & 240 degrees respectively
// and shifts for fine adjustment and to correct transformer errors.
//-----------------------------------------------------------------------------
phaseShiftedV1 = lastFilteredV + Phasecal1 * (filteredV - lastFilteredV);
phaseShiftedV2 = storedV[(numberOfSamples-PHASE2-1)%PHASE3]
+ Phasecal2 * (storedV[(numberOfSamples-PHASE2)%PHASE3]
- storedV[(numberOfSamples-PHASE2-1)%PHASE3]);
phaseShiftedV3 = storedV[(numberOfSamples+1)%PHASE3]
+ Phasecal3 * (storedV[(numberOfSamples+2)%PHASE3]
- storedV[(numberOfSamples+1)%PHASE3]);
//-----------------------------------------------------------------------------
// F) Instantaneous power calc
//-----------------------------------------------------------------------------
instP1 = phaseShiftedV1 * filteredI1; //Instantaneous Power
sumP1 +=instP1; //Sum
instP2 = phaseShiftedV2 * filteredI2;
sumP2 +=instP2;
instP3 = phaseShiftedV3 * filteredI3;
sumP3 +=instP3;
numberOfPowerSamples++; //Count number of times looped for Power averages.
}
//-----------------------------------------------------------------------------
// G) Find the number of times the voltage has crossed the initial voltage
// - every 2 crosses we will have sampled 1 wavelength
// - so this method allows us to sample an integer number of half wavelengths which increases accuracy
//-----------------------------------------------------------------------------
lastVCross = checkVCross;
if (sampleV > startV)
checkVCross = true;
else
checkVCross = false;
if (numberOfSamples==1)
lastVCross = checkVCross;
if (lastVCross != checkVCross)
crossCount++;
numberOfSamples++; //Count number of times looped.
}
//-------------------------------------------------------------------------------------------------------------------------
// 3) Post loop calculations
//-------------------------------------------------------------------------------------------------------------------------
//Calculation of the root of the mean of the voltage and current squared (rms)
//Calibration coefficients applied.
double V_Ratio = Vcal *((SupplyVoltage/1000.0) / 1023.0);
Vrms = V_Ratio * sqrt(sumV / numberOfPowerSamples);
double I_Ratio1 = Ical1 *((SupplyVoltage/1000.0) / 1023.0);
Irms1 = I_Ratio1 * sqrt(sumI1 / numberOfPowerSamples);
double I_Ratio2 = Ical2 *((SupplyVoltage/1000.0) / 1023.0);
Irms2 = I_Ratio2 * sqrt(sumI2 / numberOfPowerSamples);
double I_Ratio3 = Ical3 *((SupplyVoltage/1000.0) / 1023.0);
Irms3 = I_Ratio3 * sqrt(sumI3 / numberOfPowerSamples);
//Calculation power values
realPower1 = V_Ratio * I_Ratio1 * sumP1 / numberOfPowerSamples;
apparentPower1 = Vrms * Irms1;
powerFactor1 = realPower1 / apparentPower1;
realPower2 = V_Ratio * I_Ratio2 * sumP2 / numberOfPowerSamples;
apparentPower2 = Vrms * Irms2;
powerFactor2 = realPower2 / apparentPower2;
realPower3 = V_Ratio * I_Ratio3 * sumP3 / numberOfPowerSamples;
apparentPower3 = Vrms * Irms3;
powerFactor3 = realPower3 / apparentPower3;
//Reset accumulators
sumV = 0;
sumI1 = 0;
sumI2 = 0;
sumI3 = 0;
sumP1 = 0;
sumP2 = 0;
sumP3 = 0;
//--------------------------------------------------------------------------------------
// Include these statements for development/debugging only. Not used Gerard
/*#ifdef DEBUGGING
Serial.print("Total Samples: "); Serial.print(numberOfSamples);
Serial.print(" Power Samples: "); Serial.print(numberOfPowerSamples);
Serial.print(" Time: "); Serial.print(millis() - start);
Serial.print(" Crossings: "); Serial.println(crossCount);
for (int j=0; j<PHASE3; j++)
{
Serial.print(storedV[j]); Serial.print(" ");
Serial.println();
}
#endif*/
}
//*********************************************************************************************************************
long readVcc()
{
long result;
ADMUX = _BV(REFS0) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1);
delay(2);
ADCSRA |= _BV(ADSC);
while (bit_is_set(ADCSRA,ADSC));
result = ADCL;
result |= ADCH<<8;
result = 1126400L / result;
return result;
}

TrifasicEthernetEthercard - Historial de revisió

Enric a 20:13, 27 oct 2015

Gerard a 08:43, 27 oct 2015

Enric: Es crea la pàgina amb « #include // Used for Ethernet #define FILTERSETTLETIME 5000 // Time (ms) to allow the filters to...».